Skip to content

Shelter roofing guide

Horse shelter roofing: panels and purlins

Compare a complete shelter kit with PBR panels, Z-purlins and ridge caps for repairs, extensions and planned roofing projects.

2 min readUpdated September 12, 2026

Metal roof panels and structural purlins for loafing sheds
In this guide4 sections

Short answer

Start with one 26-gauge PBR sheet for each 3 ft of roof width, in a length that matches the roof plane; sheets run 6 ft to 24 ft, from $29.95. Use 6 in Z-purlins under a flat roof and 8 in under a sloped one; a complete shelter kit already includes its roof.

PartLengthsUseFrom
PBR sheet, 26-gauge Galvalume6, 8, 10, 12, 13, 20 or 24 ftCovers 3 ft of width$29.95
6 in Z-purlin10, 12, 20 or 25 ftFlat roofs$65
8 in Z-purlin12 or 25 ftSloped roofs$97.95
Ridge cap12 × 40 inPeak seam, bent for a 3:12 pitch$20

A complete Blacktail shelter kit includes its roof assembly. If you are repairing, extending or planning a separate roof, the roofing range includes PBR panels, Z-purlins and ridge caps.

Match replacement materials to the existing roof profile and dimensions. For a new structure, the parts list must follow a suitable roof design.

A complete roofed shelter

Compare a three-wall loafing shed, shade cover, sloped shelter or enclosed kit by its footprint and side coverage. The roof is part of the selected kit.

Confirm the supplied roof components and installation instructions with the order, particularly when the site has specific weather or permit requirements.

PBR roof panels

The range includes 26-gauge Galvalume PBR sheets from 6 ft to 24 ft long. Each sheet is a few inches wider than 3 ft and covers 3 ft once it overlaps the next sheet, so count sheets by 3 ft of coverage. Laps, overhangs and the roof slope still affect the finished coverage.

Measure along the roof plane and check the profile of adjoining sheets. The sheets fasten to the purlins with self-tapping screws that have rubber washers. Pallet freight needs a forklift to unload.

Z-purlins and ridge caps

Z-purlins are 14-gauge galvanized steel and carry the roof sheets. The 6 in profile is for flat roofs; use the 8 in profile on a sloped roof. Listed lengths are nominal: the 20 ft 6 in purlin is 21 ft overall, which leaves room to overlap at the supports. Confirm spacing, spans, laps and connections against the roof design.

A ridge cap covers the seam where two roof planes meet, such as an A-frame peak or a mare motel breezeway. Ours are 12 in by 40 in Galvalume, bent for a 3:12 pitch, and fasten with self-drilling metal screws.

Questions

Questions before you buy

Still deciding? Call (619) 914-6657

Can I order roof panels and purlins separately?

Yes. The roofing catalog sells loose PBR sheets, Z-purlins and ridge caps for repairs, extensions and planned new projects. Confirm the complete takeoff and compatibility before ordering.

Should I buy a kit or separate roofing parts?

Choose a complete shelter kit when its footprint and enclosure match the project. Separate materials require a complete parts list and a suitable roof design.

How do I choose a roof-panel length?

Measure the roof plane and account for the intended laps and overhangs. Each PBR sheet covers 3 ft of width after it overlaps the next one; confirm the sheet profile and quantity with the order.

What determines Z-purlin spacing?

The roof design, member profile, span, loads and connections determine the spacing. A product length alone is not an installation specification.

Let’s get your setup priced.

Tell us what you need and where it’s going. We’ll help you put an order together.

PBR Roof Panels23 products · from $20
Shop